ALCATEL-ENT1-TIMETRA-TC-MIB

IEEE 802.1p priority. zero is lowest, seven is highest.
-1 means not set

A unique value, greater than zero, for each interface
or interface sub-layer in the managed system. It is
recommended that values are assigned contiguously
starting from 1. The value for each interface sub-
layer must remain constant at least from one re-
initialization of the entity's network management
system to the next re-initialization.

the number of bits to match in an IP address mask.

The QTag data type is a 12-bit integer tag used to identify
a service. The values 0 and 4095 are not allowed.

The data type QTagOrZero represents a VLAN tag.

The value '0' indicates that no VLAN tag is provisioned, or that its value
is unknown.

The value used to uniquely identify an SDP Binding.
The first four octets correspond to the zero-extended
16-bit SDP ID, while the remaining four octets
correspond to the 32-bit VC ID, both encoded in network
byte order.

802.2 LLC SAP value, Source and Destination.

ServiceAdminStatus data type is an enumerated integer that
describes the values used to identify the administrative
state of a service.

ServiceOperStatus data type is an enumerated integer that
describes the values used to identify the current operational
state of a service.

The CIR rate to be used in kbps. The value -1 means maximum rate.

The data type TCpmProtPolicyID represents the identification number
of a CPM Protection policy.

The value '0' indicates that no CPM Protection policy is provisioned.

The value of a Differential Services Code Point. -1 means not set.

The name of a Differential Services Code Point value.

The name of a Differential Services Code Point value.

The value of a Differential Services Code Point.

The value of a Differential Services Code Point (DSCP). A value
of -1 means that no DSCP value is configured or available.

The value of TEgressQueueId specifies the identification number
of an egress queue. A value of zero (0) indicates that no
specific queue identification has been assigned for this object.
When an object of type TEgressQueueId is an SNMP table index,
an index value of zero (0) is not allowed and a noCreation error
will be returned.

The name of a Forwarding Class entry.

The name of a Forwarding Class entry.

This data type describes a set of Forwarding Classes.

This data type enumerates the Forwarding Classes.

The type of the frame for which this mac filter match criteria is
defined.

The value of TIngressQueueId specifies the identification number
of an ingress queue. A value of zero (0) indicates that no
specific queue identification has been assigned for this object.
When an object of type TIngressQueueId is an SNMP table index,
an index value of zero (0) is not allowed and a noCreation error
will be returned.

IP packet options octet. explanation of the octet bits:

IP OPTION NUMBERS

The Internet Protocol (IP) has provision for optional header fields
identified by an option type field. Options 0 and 1 are exactly one
octet which is their type field. All other options have their one
octet type field, followed by a one octet length field, followed by
length-2 octets of option data. The option type field is sub-divided
into a one bit copied flag, a two bit class field, and a five bit
option number. These taken together form an eight bit value for the
option type field. IP options are commonly refered to by this value.


Copy Class Number Value Name Reference
---- ----- ------ ----- ------------------------------- ---------
0 0 0 0 EOOL - End of Options List [RFC791,JBP]
0 0 1 1 NOP - No Operation [RFC791,JBP]
1 0 2 130 SEC - Security [RFC1108]
1 0 3 131 LSR - Loose Source Route [RFC791,JBP]
0 2 4 68 TS - Time Stamp [RFC791,JBP]
1 0 5 133 E-SEC - Extended Security [RFC1108]
1 0 6 134 CIPSO - Commercial Security [???]
0 0 7 7 RR - Record Route [RFC791,JBP]
1 0 8 136 SID - Stream ID [RFC791,JBP]
1 0 9 137 SSR - Strict Source Route [RFC791,JBP]
0 0 10 10 ZSU - Experimental Measurement [ZSu]
0 0 11 11 MTUP - MTU Probe [RFC1191]*
0 0 12 12 MTUR - MTU Reply [RFC1191]*
1 2 13 205 FINN - Experimental Flow Control [Finn]
1 0 14 142 VISA - Expermental Access Control [Estrin]
0 0 15 15 ENCODE - ??? [VerSteeg]
1 0 16 144 IMITD - IMI Traffic Descriptor [Lee]
1 0 17 145 EIP - Extended Internet Protocol[RFC1385]
0 2 18 82 TR - Traceroute [RFC1393]
1 0 19 147 ADDEXT - Address Extension [Ullmann IPv7]
1 0 20 148 RTRALT - Router Alert [RFC2113]
1 0 21 149 SDB - Selective Directed Broadcast[Graff]
1 0 22 150 NSAPA - NSAP Addresses [Carpenter]
1 0 23 151 DPS - Dynamic Packet State [Malis]
1 0 24 152 UMP - Upstream Multicast Pkt. [Farinacci]

[Note, an asterisk (*) denotes an obsoleted IP Option Number.]

IP protocol number. well known protocol numbers include ICMP(1),
TCP(6), UDP(17).

-1 means value not set.
-2 indicates protocol wildcard for UDP and TCP.

Description for an item. Note, use only NVT ASCII displayable characters
here, no control characters, no UTF-8, etc.

Longer description for an item. Note, use only NVT ASCII displayable
characters here, no control characters, no UTF-8, etc.

MPLS Experimental bits. -1 means not set.

This textual-convention uniquely identifies MLPPP Bundle QoS
profile in the ingress and egress MLPPP QoS profile tables.
The value 0 indicates default MLPPP QoS Profile as applicable to
a given H/W

The name of an item. When used as an index to a table, the item
name uniquely identifies the instance. When used in a reference
(TNamedItemOrEmpty) the item name entry must exist in the table.

Note, use only NVT ASCII displayable characters
here, no control characters, no UTF-8, etc.

The name of an item, or an empty string. When used in a reference
(TNamedItemOrEmpty) the item name entry must exist in the table.

Note, use only NVT ASCII displayable characters
here, no control characters, no UTF-8, etc.

The PIR rate to be used in kbps. The value -1 means maximum rate.

The PIR rate to be used in kbps. The value -1 means maximum rate.
The value 0 means undefined rate.

The PIR rate to be used in kbps. The value -1 means maximum rate.
A value of -2 specifies no override.

The identification number of a policy.

The name of a policy statement, when an object refers to it.

The Committed Information Rate (CIR) rate to be used in kbps.
The value -1 means maximum rate.

The Peak Information Rate (PIR) rate to be used in kbps.
The value -1 means maximum rate.

The value of TQueueId specifies the identification number of a
queue. A value of zero (0) indicates that no specific queue
identification has been assigned for this object. When an object
of type TQueueId is an SNMP table index, an index value of zero
(0) is not allowed and a noCreation error will be returned.

The identification number of a SAP egress policy.

The identification number of a SAP ingress policy.

The secondary shaper PIR rate to be used in Mbps.
The value -1 means maximum rate.

The number of a TCP or UDP port.
Well known port numbers include
ftp-data(20), ftp(21), telnet(23), smtp(25), http(80),
pop3(110), nntp(119), snmp(161), snmptrap(162), etc.

The operator specifies the manner in which a couple of other
MIB objects in the table are supposed to be used.

Operator Value1 Value2
----------------------------------------------------
none(0) Any(0) Any(0)
eq(1) Specified Value Any(0)
range(2) Starting Value Ending Value
lt(3) Specified Value Any(0)
gt(4) Specified Value Any(0)

'Any(0)' specifies that, this object can accept any values
but would default to 0.

The weight of the specified entity while feeding into the parent.

The TmnxActionType data type is an enumerated integer
that describes the values used to support action or
operation style commands. Setting a variable of this
type to 'doAction' causes the action to occur. GETs and
GETNEXTs on this variable return 'not-applicable'.

The TmnxAdminState data type is an enumerated integer that describes
the values used to identify the administratively desired state of
functional modules.

The TmnxAncpString data type contains a valid ancp string.

The TmnxAncpStringOrZero data type contains a valid ancp string.
An empty string indicates that no ANCP string is defined.

The data type TmnxAppProfileString denotes the application
profile string.

The data type TmnxAppProfileStringOrEmpty denotes the application
profile string. The empty string denotes the absence of a
application profile.

The value of TmnxBGPFamilyType specifies the AFI-SAFI family for
BGP peer.

an autonomous system (AS) number.

a local route preference value.

a route preference value.

TmnxBgpRouteTarget is an readable string that specifies the
extended community name to be accepted by a Route Reflector Server
or advertised by the router when reflecting any routes. I.e, it
does not apply to routes that are not reflected by the router.

A number used to identify a Customer or
Subscriber. This ID must be unique within
the Service Domain. The value 0 is used as
the null ID.

The DHCP6 messagetype.

The data type TmnxDhcpOptionType represents how the value
of this option is encoded:
- 'ipv4 (1)': this option contains an IPv4 address (4 octets)
- 'ascii(2)': this option contains seven-bit ASCII characters
- 'hex (3)': this option contains octets. It must be displayed in
hexadecimal format because it contains non-printable
characters.

This value specifies what is encoded in the Alcatel vendor specific
sub-option of option 82.

The TmnxEnabledDisabled data type is an enumerated integer that
describes the values used to identify whether an entity is
'enabled' or 'disabled'.

The value of the label used to identify the entity using the
specified encapsulation value on a specific port.

The format of this object depends on the encapsulation type
defined on this port.

When the encapsulation is nullEncap the value of this object
must be zero.

31 0
+--------+--------+--------+--------+
|00000000 00000000 00000000 00000000|
+--------+--------+--------+--------+

When the encapsulation is dot1qEncap the value of this object
is equal to the 12-bit IEEE 802.1Q VLAN ID.

31 0
+--------+--------+--------+--------+
|00000000 00000000 0000XXXX XXXXXXXX|
+--------+--------+--------+--------+

When the encapsulation is mplsEncap the value of this object
is equal to the 20-bit LSP ID.

31 0
+--------+--------+--------+--------+
|00000000 0000XXXX XXXXXXXX XXXXXXXX|
+--------+--------+--------+--------+

When the encapsulation is frEncap, the value of this object is
equal to the 10-bit Frame Relay DLCI.

31 0
+--------+--------+--------+--------+
|00000000 00000000 000000XX XXXXXXXX|
+--------+--------+--------+--------+

When the encapsulation is qinqEncap, the value of the outer
802.1Q VLAN ID is encoded in the least significant 16 bits,
and the value of the inner VLAN ID is encoded in the most
significant 16 bits.

31 0
+--------+--------+--------+--------+
|0000YYYY YYYYYYYY 0000XXXX XXXXXXXX|
+--------+--------+--------+--------+

When the encapsulation is atmEncap, the value
of the ATM VCI is encoded in the least significant
16 bits, and the value of the ATM VPI is encoded
in the next 12 bits.

For ATM VCs, the top 2 bits are 00. The value of
the ATM VCI is encoded in the least significant 16
bits, and the value of the ATM VPI is encoded in the next
12 bits.

31 0
+--------+--------+--------+--------+
|0000YYYY YYYYYYYY XXXXXXXX XXXXXXXX|
+--------+--------+--------+--------+

For ATM VPs, the top 2 bits are 01. The value of
the ATM VPI is encoded in the least significant 12 bits.

31 0
+--------+--------+--------+--------+
|01000000 00000000 0000XXXX XXXXXXXX|
+--------+--------+--------+--------+

For ATM VP ranges, the top 2 bits are 10. The value of
the start of the ATM VPI range is encoded in the least significant
12 bits, and the value of the end of the ATM VP range is encoded
in the next 12 bits.

31 0
+--------+--------+--------+--------+
|10000000 YYYYYYYY YYYYXXXX XXXXXXXX|
+--------+--------+--------+--------+

For ATM ports, the top 2 bits are 11, and the rest of the bits
must be zero.

31 0
+--------+--------+--------+--------+
|11000000 00000000 00000000 00000000|
+--------+--------+--------+--------+

When the encapsulation is wanMirrorEncap the value of this
object is equal to the 12-bit value.

31 0
+--------+--------+--------+--------+
|00000000 00000000 0000XXXX XXXXXXXX|
+--------+--------+--------+--------+

Some ports have a restrictions to the encapsulation types that
they can support and hence impose restrictions on the respective
formats defined above.

The data type TmnxIgmpGroupFilterMode describes the filter-mode of
a group.

In 'include(1)' mode, reception of packets sent to the specified
multicast address is requested only from those IPv4 Source addresses
listed in the corresponding source-list.

In 'exclude(2)' mode, reception of packets sent to the given multicast
address is requested from all IPv4 Source addresses, except those
listed in the corresponding source-list (if any).

The data type TmnxIgmpGroupType describes how a multicast group is
learned.

The data type TmnxIgmpVersion denotes the version of the IGMP protocol:
- 'version1(1)': means version 1 of the IGMP protocol
- 'version2(2)': means version 2 of the IGMP protocol
- 'version3(3)': means version 3 of the IGMP protocol.

The data type TmnxManagedRouteStatus denotes the status of a Managed Route.

The data type TmnxMldGroupFilterMode describes the filter-mode of a
group.

In 'include(1)' mode, reception of packets sent to the specified
multicast address is requested only from those IPv6 source addresses
listed in the corresponding source-list.

In 'exclude(2)' mode, reception of packets sent to the given multicast
address is requested from all IPv6 source addresses, except those
listed in the corresponding source-list (if any).

The data type TmnxMldGroupType describes how a multicast group is
learned.

The data type TmnxMldVersion denotes the version of the MLD protocol:
- 'version1(1)': means version 1 of the MLD protocol
- 'version2(2)': means version 2 of the MLD protocol

The data type TmnxMulticastAddrFamily denotes the family for
multicast protocol.

The TmnxOperState data type is an enumerated integer that describes
the values used to identify the current operational state of functional
modules.

A number used to identify an instance of OSPF.

A portid is an unique 32 bit number encoded as shown below.

32 30 | 29 26 | 25 22 | 21 16 | 15 1 |
+-----+-------+-------+-------+-------+
|000 | slot | mda | port | zero | Physical Port
+-----+-------+-------+-------+-------+

32 30 | 29 26 | 25 22 | 21 16 | 15 1 |
+-----+-------+-------+-------+-------+
|001 | slot | mda | port |channel| Channel
+-----+-------+-------+-------+-------+

Slots, mdas (if present), ports, and channels are numbered
starting with 1.

32 29 | 28 10 | 9 1 |
+---------+-------------------+-------+
| 0 1 0 0 | zeros | ID | Virtual Port
+---------+-------------------+-------+

32 29 | 28 9 | 8 1 |
+---------+---------------------+-----+
| 0 1 0 1 | zeros | ID | LAG Port
+---------+---------------------+-----+

A card port number (cpn) has significance within the context
of the card on which it resides(ie., cpn 2 may exist in one or
more cards in the chassis). Whereas, portid is an
unique/absolute port number (apn) within a given chassis.

An 'invalid portid' is a TmnxPortID with a value of 0x1e000000 as
represented below.

32 30 | 29 26 | 25 22 | 21 16 | 15 1 |
+-----+-------+-------+-------+-------+
|zero | ones | zero | zero | zero | Invalid Port
+-----+-------+-------+-------+-------+

The data type TmnxPppoeUserNameOrEmpty denotes the PPPoE username.

A number used to identify a Service. This ID
must be unique within the Service Domain.
The value 0 is used as the null ID.

The data type TmnxSlaProfileString denotes the SLA
profile string.

The data type TmnxSlaProfileStringOrEmpty denotes the SLA
profile string. The empty string denotes the absence of a
SLA profile.

The TmnxStatus data type is an enumerated integer that describes the
values used to identify the current status of functional modules in the
system such as OSPF and MPLS protocols. Setting this variable to
'create' causes instantiation of the feature in the system. Setting it
to 'delete' removes the instance and all associated configuration
information.

The value of TmnxStrSapId is a printable string which
contains the owner SAP Id or equivalent on a remote system.

The string should contain the printable string equivalent of the
textual-conventions TmnxPortID and TmnxEncapVal in the format
specified as TmnxPortID[:TmnxEncapVal]

The data type TmnxSubIdentString denotes the subscriber
identification string.

The data type TmnxSubIdentStringOrEmpty denotes the subscriber
identification string. The empty string denotes the absence of a
subscriber identification string.

The data type TmnxSubMgtIntDestId denotes the intermediate
destination id.

The data type TmnxSubMgtIntDestIdOrEmpty denotes the intermediate
destination id. The empty string denotes the absence of an
intermediate destination id.

The data type TmnxSubProfileString denotes the subscriber
profile string.

The data type TmnxSubProfileStringOrEmpty denotes the subscriber
profile string. The empty string denotes the absence of a
subscriber profile.

The identifying value for a BGP-VPRN tunnel. Depending on the
tunnel type the associated tunnel-id may be an sdp-id, an lsp-id
or zero(0).

The type of this tunnel entity.

The VPRN route distinguisher is a 8-octet object. It contains a
2-octet type field followed by a 6-octet value field. The type
field specify how to interpret the value field.

Type 0 specifies two subfields as a 2-octet administrative field
and a 4-octet assigned number subfield.

Type 1 specifies two subfields as a 4-octet administrative field
which must contain an IP address and a 2-octet assigned number
subfield.

Type 2 specifies two subfields as a 4-octet administrative field
which contains a 4-octet AS number and a 2-octet assigned number
subfield.

A number used to identify a virtual router instance in the system.

A number used to identify a virtual router instance in the system.
The number 0 will have special significance in the context the TC
is used.

A unique value, greater than zero, for each Label
Switched Path in the managed system.

A 32 bit number is used to identify a VC(Virtual Circuit).
The VC ID cannot be 0.

A 32 bit number is used to identify a VC(Virtual Circuit).
A value of 0 indicates no VC ID is configured or
available.

The value of TmnxVcType is an enumerated integer that
indicates a Virtual Circuit (VC) type. 'frDlciMartini(1)'
replaces the old 'frDlci' when used over martini tunnels.