ALCATEL-ENT1-IPV6-MIB Table View

Table allowing the creation and removal of IPv6
interfaces.
          
The table is indexed by ipv6IfIndex.  The value of
ipv6IfIndex shall be a four byte value in one of
the following formats:
          
  0x0000vvvv - The interface for VLAN vvvv
  0x0100tttt - The interface for tunnel tttt
  0x02000001 - The IPv6 loopback interface
  0x0300nnnn - A loopback0 interface with ID nnnn
          
The IPv6 loopback interface's configuration cannot be
	modified.
          
	A loopback0 interface's configuration cannog be modified
	other than to change its name or administrative status.
	When creating a new loopback0 interface, the special
	ipv6IfIndex value of 0x03000000 should be specified 
	(ID of 0).  Upon creation the interface will automatically
	be assigned its actual ID and ipv6IfIndex.

alaIPv6InterfaceEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1

An IPv6 interface entry.

Indexes

IPV6-MIBipv6IfIndex

Column	Syntax	OID
alaIPv6InterfaceRowStatus Used to control the addition and removal of IPv6 interfaces.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.1
alaIPv6InterfaceDescription The IPv6 interface's description.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.2
alaIPv6InterfaceMtu The IPv6 interface's maximum transmission unit.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.3
alaIPv6InterfaceType The interface type.	Enumeration Enumerated Values: 1 other 2 vlan 3 tunnel 4 loopback	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.4
alaIPv6InterfaceAdminStatus Interface administrative status.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.5
alaIPv6InterfaceSendRouterAdvertisements Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is enable(1). Some interface types (e.g. 6to4 t…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.6
alaIPv6InterfaceMaxRtrAdvInterval The maximum time allowed between sending unsolicited multicast router advertisements from the interface.	secondsUnsigned32r/w Constraints: range: 4-1800	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.7
alaIPv6InterfaceAdvManagedFlag The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.8
alaIPv6InterfaceAdvOtherConfigFlag The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.9
alaIPv6InterfaceAdvReachableTime The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router.	millisecondsUnsigned32r/w Constraints: range: 0-3600000	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.10
alaIPv6InterfaceAdvRetransTimer The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router.	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.11
alaIPv6InterfaceAdvDefaultLifetime The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds. …	secondsUnsigned32r/w Constraints: range: 0-9000	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.12
alaIPv6InterfaceName The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically assigned.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.13
alaIPv6InterfaceAdvSendMtu The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.14
alaIPv6InterfaceReachableTime In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioning to the stale state. Computed to be between .5 and 1.5 ti…	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.15
alaIPv6InterfaceBaseReachableTime The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above.	secondsUnsigned32r/w Constraints: range: 10-3600	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.16
alaIPv6InterfaceMinRtrAdvInterval The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more than .75 times the value of alaIPv6InterfaceMax…	secondsUnsigned32r/w Constraints: range: 0-1350	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.17
alaIPv6InterfaceClockSkew Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly synchronized clocks.	secondsUnsigned32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.18
alaIPv6InterfaceRetransTimer The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery.	millisecondsUnsigned32r/w Constraints: range: 1000-30000	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.19
alaIPv6InterfaceDADTransmits The number of Neighbor Solicitations to send during Duplicate Address Detection. A value of 0 indicates that DAD will not be performed for addresses assigned to the interface.	Unsigned32r/w Constraints: range: 0-10	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.20
alaIPv6InterfaceAdvHopLimit The value placed in the current hop limit field of router advertisements.	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.21
alaIPv6InterfaceLPND Enable/disable local proxy neighbor discovery.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.22
alaIPv6InterfaceRAFilterdeprecated Enable/disable RA filtering. This object has been superseded by the alaIPv6RAFilterInterfaceTable.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.23
alaIPv6InterfaceNeighborLimit The maximum number o neighbor entries that may be cached on this interface. A value of 0 indicates that no limit is set. The minimum value is 10.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.24
alaIPv6InterfaceRetransBackoff The neighbor unreachability detection exponential backoff base. A value of 1 indicates the use of fixed interval retransmissions.	Unsigned32r/w Constraints: range: 1-3	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.25
alaIPv6InterfaceRetransMax The maximum number of neighbor solicitations to be sent during neighbor discovery or neighbor unreachability detection.	Unsigned32r/w Constraints: range: 1-10	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.26
alaIPv6InterfaceRouterPreference The preference a host should give to using this router as a default router.	Enumerationr/w Enumerated Values: 0 medium 1 high 3 low	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.27

Table for IPv6 configured tunnels.  This table contains the
tunnel-specific information extending the corresponding
tunnel interface entry in alaIPv6InterfaceTable.

alaIPv6ConfigTunnelEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1

A entry contains the objects for an IPv6 configured tunnel.

Indexes

IPV6-MIBipv6IfIndex

Column	Syntax	OID
alaIPv6ConfigTunnelV4Source The source IPv4 address for the tunnel.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.1
alaIPv6ConfigTunnelV4Dest The destination IPv4 address for the tunnel.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.2

Table allowing the creation and removal of IPv6
addresses assigned to interfaces.

alaIPv6InterfaceAddressEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1

An IPv6 interface address entry.

The same link-local address may be assigned to
multiple interfaces. A global address may only
be assigned to a single interface.

Indexes

IPV6-MIBipv6IfIndex alaIPv6InterfaceAddress

Column	Syntax	OID
alaIPv6InterfaceAddressRowStatus Used to control the addition and removal of IPv6 interface addresses.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.1
alaIPv6InterfaceAddress An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.2
alaIPv6InterfaceAddressPrefixLength The number of bits that are significant in the IPv6 address' prefix.	Unsigned32r/w Constraints: range: 3-128	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.3
alaIPv6InterfaceAddressAnycastFlag This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.4
alaIPv6InterfaceAddressDADStatus The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such cases, duplicate address detection will be performed again …	Enumerationr/w Enumerated Values: 0 unknown 1 pending 2 duplicate 3 passed 4 check	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.5

Table allowing the creation and removal of IPv6
addresses formed by appending an EUI-64 interface
identifier to the specified prefix.
          
This table is mainly used for the creation of such
addresses.  After creation they can be managed
via the alaIPv6InterfaceAddressTable.

alaIPv6InterfaceEUI64AddressEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1

An IPv6 interface EUI-64 address entry.

Indexes

IPV6-MIBipv6IfIndex alaIPv6InterfaceEUI64AddressPrefix

Column	Syntax	OID
alaIPv6InterfaceEUI64AddressRowStatus Used to control the addition and removal of IPv6 interface EUI-64 addresses.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.1
alaIPv6InterfaceEUI64AddressPrefix The prefix for the EUI-64 address.	AlaIPv6AddressPrefix Type Constraints: range: 8	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.2
alaIPv6InterfaceEUI64AddressPrefixLength The number of bits that are significant in the IPv6 address' prefix. The prefix length must be in the range 3..64 or 128.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.3
alaIPv6InterfaceEUI64AddressIdentifier The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.4

The IPv6 neighbor table.  Much of this information is
available in the RFC-2465 ipv6NetToMediaTable.  However,
that table does not allow the static configuration of
neighbor entries (all objects except for
ipv6NetToMediaValid are read-only).

alaIPv6NeighborEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1

Each entry contains one IPv6 address to `physical'
address equivalence (a neighbor).

Indexes

IPV6-MIBipv6IfIndex alaIPv6NeighborNetAddress

Column	Syntax	OID
alaIPv6NeighborNetAddress The neighbor's IPv6 Address.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.1
alaIPv6NeighborPhysAddress The neighbor's media-dependent `physical' address.	SNMPv2-TCPhysAddressr/w Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.2
alaIPv6NeighborSlotdeprecated The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not applicable. Superseded by alaIPv6NeighborPo…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.3
alaIPv6NeighborPortdeprecated The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not applicable. Superseded by alaIPv6NeighborPo…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.4
alaIPv6NeighborType The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that …	Enumeration Enumerated Values: 1 other 2 dynamic 3 static 4 local	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.5
alaIPv6NeighborStatedeprecated The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used.	Enumeration Enumerated Values: 1 reachable 2 stale 3 delay 4 probe 5 invalid 6 unknown	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.6
alaIPv6NeighborLastUpdated The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.7
alaIPv6NeighborRowStatus Used to control the addition and removal of static entries in the neighbor table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.8
alaIPv6NeighborLifetime The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero indicates the neighbor will remain in its current state inde…	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.9
alaIPv6NeighborReachability The reachability status of the neighbor.	Enumeration Enumerated Values: 1 confirmed 2 unconfirmed 3 incomplete	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.10
alaIPv6NeighborChassisdeprecated On a multi-chasis system, the chassis used to reach the neighbor. On a single-chassis system this value is always 0. On read, a value of zero may indicate that the chassis is not known/not applicable. S…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.11
alaIPv6NeighborPortIfIndex The ifIndex of the physical port or link aggregation used to reach the neighbor. When creating a static neighbor the port ifIndex must be specified. On read, a value of zero indicates the port ifIndex is not known/…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.12

This table has been superseded by alaIprmV6StaticRouteTable in
ALCATEL-IND1-IPRMV6-MIB.
          
Table allowing the creation and removal of static
IPv6 routes.

alaIPv6StaticRouteEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1

A static route entry.

Indexes

alaIPv6StaticRouteDest alaIPv6StaticRoutePfxLength

Column	Syntax	OID
alaIPv6StaticRouteDestobsolete The destination IPv6 address of this static route. This object may not take a Multicast address value.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.1
alaIPv6StaticRoutePfxLengthobsolete Indicates the prefix length of the destination address.	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.2
alaIPv6StaticRouteIfIndexobsolete If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop address types the value is zero.	IPV6-TCIpv6IfIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.3
alaIPv6StaticRouteNextHopobsolete The IPv6 address of the next hop towards the destination.	IPV6-TCIpv6Addressr/w Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.4
alaIPv6StaticRouteMetricobsolete The routing metric for this route. The lower the value, the higher the priority for the static route.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.5
alaIPv6StaticRouteRowStatusobsolete Used to control the addition and removal of static routes.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.6

Local table mapping host names to IPv6 addresses. This provides
the equivalent of /etc/hosts for IPv6.

alaIPv6HostEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1

A entry maps a host name to an IPv6 address.

Indexes

alaIPv6HostName alaIPv6HostAddress

Column	Syntax	OID
alaIPv6HostName A host name to be mapped to an IPv6 address.	OctetString Constraints: range: 1-64	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.1
alaIPv6HostAddress The IPv6 address mapped to the host name.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.2
alaIPv6HostRowStatus Allows host name/IPv6 address mappings to be created and deleted in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.3

Table allowing the creation and removal of IPv6
prefixes to be placed in Prefix Information
options in Router Advertisement messages sent
from the interface.
          
Default: all prefixes that the router advertises
via routing protocols as being on-link for the
interface from which the advertisement is sent.
The link-local prefix is not included in the
list of advertised prefixes.

alaIPv6InterfacePrefixEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1

An IPv6 interface prefix entry.

Indexes

IPV6-MIBipv6IfIndex alaIPv6InterfacePrefix alaIPv6InterfacePrefixLength

Column	Syntax	OID
alaIPv6InterfacePrefixRowStatus Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.1
alaIPv6InterfacePrefix The prefix associated with this interface.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.2
alaIPv6InterfacePrefixLength The length of the prefix in bits.	Unsigned32 Constraints: range: 1-127	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.3
alaIPv6InterfacePrefixValidLifetime The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.4
alaIPv6InterfacePrefixOnLinkFlag The value to be placed in the on-link flag (L-bit) field in the Prefix Information option.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.5
alaIPv6InterfacePrefixPreferredLifetime The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.6
alaIPv6InterfacePrefixAutonomousFlag The value to be placed in the Autonomous Flag field in the Prefix Information option.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.7
alaIPv6InterfacePrefixSource The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration the value will be dynamic(2).	Enumeration Enumerated Values: 1 other 2 dynamic 3 configured	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.8
alaIPv6InterfacePrefixValidLifetimeDecrement If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixValidLifetime.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.9
alaIPv6InterfacePrefixValidLifetimeExpire The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true.	SNMPv2-TCDateAndTimer/w Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.10
alaIPv6InterfacePrefixPreferredLifetimeDecrement If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixPreferredLifetime.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.11
alaIPv6InterfacePrefixPreferredLifetimeExpire The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true.	SNMPv2-TCDateAndTimer/w Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.12

Table allowing the retrieval of the known IPv6
path MTU value.

alaIPv6PMTUEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1

An IPv6 path MTU entry.

Indexes

alaIPv6PMTUDest

Column	Syntax	OID
alaIPv6PMTUDest The destination address of the IPv6 path.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.1
alaIPv6PMTU The path's MTU.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.2
alaIPv6PMTUExpire The minimum time remaining before the PMTU entry is removed from the table.	minutesSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.3
alaIPv6PMTUHits The number of times the path MTU entry has been used.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.4
alaIPv6PMTUUpdates The number of times the path MTU entry has been updated.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.5

Table allowing the retrieval of the flags for
IPv6 route entries.

alaIPv6RouteFlagsEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1

An IPV6 route flags entry.

Indexes

No indexes recorded

Column	Syntax	OID
alaIPv6RouteFlagsUp True if the Up (U) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.1
alaIPv6RouteFlagsGateway True if the Gateway (G) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.2
alaIPv6RouteFlagsHost True if the Host (H) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.3
alaIPv6RouteFlagsStatic True if the Static (S) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.4
alaIPv6RouteFlagsCloneable True if the Cloneable (C) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.5
alaIPv6RouteFlagsDiscard True if the Discard/Blackhole (B) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.6
alaIPv6RouteFlagsECMP True if the ECMP (E) flag is set on the route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.7
alaIPv6RouteFlagsTransient True if route has not been replaced by valid route after takeover.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.8

Table allowing the creation and removal of local IPv6
unicast addresses (RFC 4193) on an interface.

alaIPv6LocalUnicastEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1

An local unicast IPv6 address entry.

Indexes

IPV6-MIBipv6IfIndex alaIPv6LocalUnicastGlobalID alaIPv6LocalUnicastSubnetID alaIPv6LocalUnicastInterfaceID

Column	Syntax	OID
alaIPv6LocalUnicastGlobalID The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value.	OctetString Constraints: range: 5-5	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.1
alaIPv6LocalUnicastSubnetID The subnet ID portion of the local IPv6 unicast address.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.2
alaIPv6LocalUnicastInterfaceID The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.3
alaIPv6LocalUnicastPrefixLength The number of bits that are significant in the IPv6 address prefix.	Unsigned32r/w Constraints: range: 64-128	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.4
alaIPv6LocalUnicastEUI64 If true(1) the interface identifier is formed from an automatically generated EUI-64 value.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.5
alaIPv6LocalUnicastRowStatus Used to control the addition and removal of local IPv6 unicast addresses.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.6

Table to control operation of RA Filtering on a VLAN.

alaIPv6RAFilterInterfaceEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1

An RA filter interface entry.

Indexes

alaIPv6RAFilterInterfaceVlan

Column	Syntax	OID
alaIPv6RAFilterInterfaceVlan The ID of the VLAN on which RA Filtering is to be configured.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.1
alaIPv6RAFilterInterfaceAdminStatus RA filtering administrative status.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.2
alaIPv6RAFilterInterfaceRowStatus Used to control the addition and removal of an interface's RA filter configuration.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.16.1.3

Table allowing the creation and removal of trusted sources
for a VLAN's RA filtering.

alaIPv6RAFilterTrustedSourceEntry row .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1

An RA filter trusted source entry.

Indexes

alaIPv6RAFilterInterfaceVlan alaIPv6RAFilterTrustedSourceType alaIPv6RAFilterTrustedSourceValue

Column	Syntax	OID
alaIPv6RAFilterTrustedSourceType The type of the trusted source selector.	AlaIPv6RAFilterTrustedSourceType Type Values: 1 port 2 netAddress 3 physAddress	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.1
alaIPv6RAFilterTrustedSourceValue The trusted source selector's value.	AlaIPv6RAFilterTrustedSourceValue Type Constraints: range: 1..255	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.2
alaIPv6RAFilterTrustedSourceRowStatus Used to control the addition and removal of a trusted source entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6486.801.1.2.1.29.1.1.17.1.3