ADTRAN-GENERIC-VECTORING-MIB Table View

This table contains global vectoring configuration
parameters, per populated card slot.

adGenVectorModuleConfEntry row .1.3.6.1.4.1.664.5.70.57.1.1.1

This list contains vector limits per module .

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenVectorModuleConfSupportedVectorModeTypes Indicates the vectoring modes in which the card is capable of participating.	AdGenVectorMode Type Values: 1 blv 2 slv 3 both 4 none 5 dlv 7 blv-dlv-slv	.1.3.6.1.4.1.664.5.70.57.1.1.1.1
adGenVectorModuleConfMaxBLVGroups The maximum number of Board-Level vectoring groups the module can support.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.1.1.2
adGenVectorModuleConfMaxSLVGroups The maximum number of System-Level vectoring groups the module can support.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.1.1.3
adGenVectorModuleConfMaxPhysPerSLVGroup The maximum number of physical ports available per System-Level vectoring group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.1.1.4
adGenVectorModuleConfNumPhys The number of physical ports available for vectoring on the given slot.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.1.1.5
adGenVectorModuleConfVectorEngineHwRev The hardware revision of the vectoring engine chip set.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.1.1.6
adGenVectorModuleConfVectorEngineSwRev The software revision of the vectoring engine chip set.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.1.1.7

The Vectoring Group Table.  A unique group is created for each
unique set of physical ports that will be independently vectored.

adGenVectorGroupEntry row .1.3.6.1.4.1.664.5.70.57.1.3.1

An entry in the Vectoring Group table.

Indexes

adGenVectorGroupIfIndex

Column	Syntax	OID
adGenVectorGroupIfIndex The ifIndex value of the interface associated with this Vectoring Group. The IANA type should be linegroup (210).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.3.1.1
adGenVectorGroupDescription The textual name given to this group.	OctetStringr/w Constraints: range: 1-80	.1.3.6.1.4.1.664.5.70.57.1.3.1.2
adGenVectorGroupLastError The string describing the last error experienced.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.3.1.3
adGenVectorGroupBandPlan The superset band plan for the vectoring group. An individual port in the vectoring group must be a subset of the group's band plan. Valid options listed below: g998 (1) -- Annex A (EU32) g998e (2) …	AdGenVectorGroupBandPlansr/w Type Values: 1 g998 2 g998e 3 g998ade 4 g997 5 g997e 6 hpe	.1.3.6.1.4.1.664.5.70.57.1.3.1.4
adGenVectorGroupRowStatus This object is used to create a new row or modify or delete an existing row in this table. Setting this value to 'active' indicates that the vectoring group is administratively In-Service. Setting this value to 'inactiv…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.70.57.1.3.1.5
adGenVectorGroupFallbackMode The vectoring group fallback mode determines port behavior during misconfiguration and system failure events. Valid options listed below: adsl2-multimode (1) -- DEPRECATED, this value will change the mode to adsl2…	AdGenVectorGroupFallbackModesr/w Type Values: 1 adsl2-multimode 2 shutdown 3 adsl2 4 non-vectored	.1.3.6.1.4.1.664.5.70.57.1.3.1.6
adGenVectorGroupFallbackAlarmSeverity Sets the severity for adGenVectorAlarmsForcedFallbackAlarm. This severity applies to the entire group, which may span several slots. Valid options listed below: critical (0) major (1) minor (2) …	Enumerationr/w Enumerated Values: 0 critical 1 major 2 minor 3 alert 4 info	.1.3.6.1.4.1.664.5.70.57.1.3.1.7
adGenVectorGroupFallbackAlarmEnable Controls whether the adGenVectorAlarmsForcedFallback alarm is generated when the alarm condition is active. This selection applies to the entire group, which may span several slots. Valid options listed below: disab…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.664.5.70.57.1.3.1.8
adGenVectorGroupVectoringMode Controls the vectoring mode in which the card is currently operating. Valid options listed below: blv (1) -- Board Level Vectoring is vectoring of physical ports on a single board. slv (2) -- System Level …	AdGenVectorModer/w Type Values: 1 blv 2 slv 3 both 4 none 5 dlv 7 blv-dlv-slv	.1.3.6.1.4.1.664.5.70.57.1.3.1.9
adGenVectorGroupAutoAddEnable Controls whether a slot is automatically added to a System Level vecotoring group when Inserted into a shelf: disable (0) -- auto add disabled enable (1) -- auto add enabled	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.664.5.70.57.1.3.1.10

Row creation adds/maps the physical port to a vectoring group.

adGenVectorPhyMapEntry row .1.3.6.1.4.1.664.5.70.57.1.5.1

An entry in the Phy Map table.
This entry is represents one port that
is associated with a vectoring group.

Indexes

adGenVectorPhyMapGroupIfIndex adGenVectorPhyMapPhyIfIndex

Column	Syntax	OID
adGenVectorPhyMapGroupIfIndex The ifIndex value of the vectoring group to which the physical port is mapped.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.5.1.1
adGenVectorPhyMapPhyIfIndex The ifIndex value of the physical port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.5.1.2
adGenVectorPhyMapLastChange The value of sysUpTime at the time this Group-Phy mapping entered its current operational state.	AdGenVectorLastChange	.1.3.6.1.4.1.664.5.70.57.1.5.1.3
adGenVectorPhyMapLastError The string describing the last error experienced.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.5.1.4
adGenVectorPhyMapRowStatus This object is used to create a new row or modify or delete an existing row in this table. Creating a row adds the Phy to the Group. Setting this value to 'active' indicates that the Group-Phy mapping is administrativel…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.70.57.1.5.1.5

The Vectoring Group Status Table displays the status of
each vectoring group.

adGenVectorGroupStatusEntry row .1.3.6.1.4.1.664.5.70.57.1.6.1

An entry in the Vectoring Group table.

Indexes

adGenVectorGroupStatusIfIndex

Column	Syntax	OID
adGenVectorGroupStatusIfIndex The ifIndex value of the interface associated with this Vectoring Group. The IANA type should be linegroup (210).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.6.1.1
adGenVectorGroupStatusNumProvisionedPorts The number of ports assigned to this vectoring group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.2
adGenVectorGroupStatusNumVectoredPorts The number of ports assigned to this vectoring group that are trained and being vectored (g993.5).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.3
adGenVectorGroupStatusNumUntrainedPortsdeprecated The number of ports assigned to this vectoring group that are not currently trained.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.4
adGenVectorGroupStatusNumVectorFriendlyPorts The number of ports assigned to this vectoring group that are trained and are vectoring friendly (g993.2 annex y).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.5
adGenVectorGroupStatusNumNonVectoredPorts The number of ports assigned to this vectoring group that are trained and are not vectored.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.6
adGenVectorGroupStatusNumLegacyPorts The number of ports assigned to this vectoring group that are trained with a legacy VDSL2 modem that does not support vectoring.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.7
adGenVectorGroupStatusOperStatus The current operational status of the vectoring group.	AdGenVectorGroupOperStatus Type Values: 1 up 2 down 3 upPartial	.1.3.6.1.4.1.664.5.70.57.1.6.1.8
adGenVectorGroupStatusReset A SET clears the status information for each interface in the specified group. A GET will always return a one (1).	Enumerationr/w Enumerated Values: 1 reset	.1.3.6.1.4.1.664.5.70.57.1.6.1.9
adGenVectorGroupStatusNumFallbackPorts The number of ports assigned to this vectoring group that have been forced into the fallback mode specified by adGenVectorGroupFallbackMode.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.1.6.1.10

Displays the status of the available physical ports in the system,
including the group, if any, a physical port is associated with.
It also indicates the installed status of a certain physical port
along with the type of group to which the physical port is installed.

adGenVectorPhyStatusEntry row .1.3.6.1.4.1.664.5.70.57.1.7.1

An entry in the Physical Port Status table.
This entry represents one physical port.

Indexes

adGenVectorPhyStatusPhyIfIndex

Column	Syntax	OID
adGenVectorPhyStatusPhyIfIndex The ifIndex value of the physical link. IANA type is propVirtual(53).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.7.1.1
adGenVectorPhyStatusGroupIfIndex The ifIndex value of the Group of which this physical link belongs. A value of '0' indicates that the link is currently not mapped to any Group. IANA type is linegroup(210).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.1.7.1.2
adGenVectorPhyStatusGroupType Indicates this physical port's vectoring group type, if any.	AdGenVectorMode Type Values: 1 blv 2 slv 3 both 4 none 5 dlv 7 blv-dlv-slv	.1.3.6.1.4.1.664.5.70.57.1.7.1.3
adGenVectorPhyStatusPortLineStatedeprecated The line state of the physical port.	AdGenVectorPhyLineState Type Values: 0 notAvailable 1 down 2 train 3 up 4 deltActive 5 deltDataExchange 6 deltDataRequest 7 deltComplete 8 seltActive 9 seltDataRequest 10 seltComplete	.1.3.6.1.4.1.664.5.70.57.1.7.1.4
adGenVectorPhyStatusPortVectoringState The vectoring state of a physical port. The ff suffix designates vectoring friendly states.	AdGenVectorPhyPortVectoringState Type Values: 0 idle 1 dsInit-1-0 2 dsInit-2-1 3 usInit-1 4 usInit-2 5 steady 6 trans 7 waitForStart 8 dsInit-1-1 9 dsInit-2-0 10 reset 11 nonVectoring 12 handshake 13 waitForStart-Legacy 14 init-Legacy 15 steady-Legacy 16 steadyB 17 stopPending 18 idle-FF 19 dsInit-1-0-ff 20 dsInit-2-1-ff 21 usInit-1-ff 22 usInit-2-ff 23 steady-ff 24 trans-ff 25 waitForStart-ff 26 dsInit-1-1-ff 27 dsInit-2-0-ff 28 steadyB-ff 29 stopPending-ff 30 unknown 31 fallback	.1.3.6.1.4.1.664.5.70.57.1.7.1.5
adGenVectorPhyStatusVectoringError The last error received in relation to the physical port.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.7.1.6
adGenVectorPhyStatusVectoringErrorTimestamp The card uptime when the last physical port error occurred. If no error has occurred, this value will be zero.	secondsAdGenVectorPhyPortErrorTimestamp	.1.3.6.1.4.1.664.5.70.57.1.7.1.7
adGenVectorPhyStatusVectoringErrorDateTime Date/time string in format yyyy.MM.dd HH:mm of the last physical port error. If no error has occurred, the value will be N/A.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.70.57.1.7.1.8

Table contains slot based vectoring configuration items

adGenVectorSlotConfEntry row .1.3.6.1.4.1.664.5.70.57.1.9.1

Each entry can be applied per vectored slot.

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenVectorSlotConfForceFallback Used to manually force slot into or out of vectoring fallback mode. A read will always return allowVectoring (2)	Enumerationr/w Enumerated Values: 1 forceSlotFallback 2 allowVectoring	.1.3.6.1.4.1.664.5.70.57.1.9.1.1

Table contains slot based vectoring status items

adGenVectorSlotStatusEntry row .1.3.6.1.4.1.664.5.70.57.1.10.1

Each entry can be read per vectored slot

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenVectorSlotStatusFallbackState Used to query the slot fallback state.	Enumeration Enumerated Values: 1 fallbackActive 2 fallbackInactive	.1.3.6.1.4.1.664.5.70.57.1.10.1.1

Table contains instances that are created when there is a request to reserve a bulk vector instance

adGenVectorBulkInstanceEntry row .1.3.6.1.4.1.664.5.70.57.2.1.1

Index is the slot number.

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenVectorBulkReserveSlotInstance Used to index the TLV table; Each time this is called by slot it creates an instance for that viewer. Once an instance is created, it may be found by doing a get on adTa5kTlvBySlotInstance with the instance number	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.2.1.1.1

Table contains filters that can be applied on the requested instance

adGenVectorBulkFilterEntry row .1.3.6.1.4.1.664.5.70.57.2.2.1

Indexes are the vector group status index and instance number

Indexes

adGenVectorGroupStatusIfIndex adGenVectorBulkFilterInstance

Column	Syntax	OID
adGenVectorBulkFilterInstance Used to index the table by TLV Instance number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.2.2.1.1
adGenVectorBulkFilterInterface Used to set the vector group filter for a specific bulk vector instance of the Tlv table. The interface ID passed here will be the SNMP interface ID.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.70.57.2.2.1.2
adGenVectorBulkFilterSlot Used to set the slot of bulk vector info to return in the bulk vector instance	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.70.57.2.2.1.3
adGenVectorBulkFilterDirection Used to set the direction of bulk vector info to return in the bulk vector instance: 1 - Upstream Direction, 2 - Downstream direction	Enumerationr/w Enumerated Values: 1 upstream 2 downstream	.1.3.6.1.4.1.664.5.70.57.2.2.1.4
adGenVectorBulkFilterType Used to set the type of bulk vector info to return in the bulk vector instance: 1 - weights	Enumerationr/w Enumerated Values: 1 weights	.1.3.6.1.4.1.664.5.70.57.2.2.1.5
adGenVectorBulkSlotCreate Set this OID to 1 to update the instance with bulk vector info depending on filters. A get on this OID always returns a 1.	Enumerationr/w Enumerated Values: 1 updateinstance	.1.3.6.1.4.1.664.5.70.57.2.2.1.6