ADTRAN-GENERIC-BRIDGE-MIB Table View

This table contains global bridge configuration
parameters, per populated card slot.

adGenBridgeModuleConfEntry row .1.3.6.1.4.1.664.5.67.1.16.1.1.1

This list contains bridge group limits per module .

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenBridgeModuleMaxBridges The maximum number of bridges this module will support.	Integer32 Constraints: range: 0-100	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.1
adGenBridgeModuleMaxPhyls The total number of physical links that may be mapped to bridges on the module, including active and inactive mappings.	Integer32 Constraints: range: 0-2200	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.2
adGenBridgeModuleConfBridges The current number of bridges configured on the module.	Integer32 Constraints: range: 0-100	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.3
adGenBridgeModuleConfPhyls The total number of physical links currently mapped to bridges on the module, including in-service and out-of-service mappings.	Integer32 Constraints: range: 0-2200	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.4
adGenBridgeModuleMaxBandwidth The maximum bandwith allocated for this module in kbps.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.5
adGenBridgeModuleConfBandwidth The bandwidth currently being used by this module in kbps.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.1.1.6

The Bridge table.  A unique Bridge is created
for every bonding or bridging instance, with an associated
type that determines its functionality.

adGenBridgeEntry row .1.3.6.1.4.1.664.5.67.1.16.1.3.1

An entry in the Bridge table. This entry is
used to model a single instance of an aggregation
(bridging or bonding) engine.

Indexes

adGenBridgeIfIndex

Column	Syntax	OID
adGenBridgeIfIndex The ifIndex value of the interface associated with this Bridge. The IANA type should be linegroup (210).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.1
adGenBridgeType The intended type of this bridge EFM, IMA, TR-101, etc.	AdGenBridgeTyper/w Type Values: 1 notProvisioned 2 efm 3 tr101 4 ima 5 linkAggregation 6 macSwitched 7 ppp 8 atm	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.2
adGenBridgeName The textual name given to this Bridge.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.3
adGenBridgeProtMode The protection mode of the group single-slot (not protectable), unprotected (but potentially protectable), or protected.	AdGenBridgeProtMode Type Values: 1 unsupported 2 unprotected 3 protected	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.4
adGenBridgeProtAvail Indicates if the selected protection slot is available for protection switchover.	AdGenBridgeProtAvail Type Values: 1 unsupported 2 unavailable 3 available	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.5
adGenBridgeProtState Indicates if the protection card is actively running this bridge.	AdGenBridgeProtState Type Values: 1 unsupported 2 unprotected 3 protected	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.6
adGenBridgeProtSlot A bit map of Protection Module slots part of this Protection Group. Slot 1 0x00000001 Slot 2 0x00000002 Slot 3 0x00000004 Slot 4 0x00000008 Slot 5 0x00000010 | | Slot 30 0x20000000 Slot 31 0…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.7
adGenBridgeMinNumActivePhyls The minimum number of active PHYLS that have to be mapped to this group before the OperStatus of the bridge can be declared to be 'up'. If the active number ever drops below this number then the Bridge will enter an Ope…	Integer32r/w Constraints: range: 1-16	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.8
adGenBridgeOperStatus The current operational status of the local end of the group.	AdGenBridgeOperStatus Type Values: 1 up 2 down 3 testing 4 noLinksInGroup 5 upPartial	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.9
adGenBridgeLastChange The value of sysUpTime at the time this Bridge group entered its current operational state.	AdGenBridgeLastChange	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.10
adGenBridgeNumCfgEVPLs The number of EVPLs currently assigned against the ifIndex of this bridge. This value is incremented by the agent upon the creation of an EVPL against this bridge and decremented upon the deletion of an EVPL that was as…	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.11
adGenBridgeNumCfgEVCLs The number of EVCLs currently assigned against the ifIndex of this bridge. This value is incremented by the agent upon the creation of an EVCL against this bridge and decremented upon the deletion of an EVCL that was as…	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.12
adGenBridgeNumCfgPhyls The number of PHYLs currently mapped to this bridge. This value is incremented by the agent upon the creation of a Bridge-PHYL mapping.	Integer32 Constraints: range: 0-2200	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.13
adGenBridgeNumActPhyls The number of PHYLs currently active as part of this group.	Integer32 Constraints: range: 0-2200	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.14
adGenBridgeLastError The string describing the last error experienced.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.15
adGenBridgeRowStatus This object is used to create a new row or modify or delete an existing row in this table. Setting this value to 'active' indicates that the Bridge is administratively In-Service. Setting this value to 'inactive' indica…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.16
adGenBridgeMaxBandwidth The maximum bandwidth allocated for this bridge in kbps.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.17
adGenBridgeCurrentBandwidth The bandwith currently used by this bridge in kpbs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.18
adGenBridgeUpstreamRate The Upstream Rate configured on the bridge in kbps.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.19
adGenBridgeDownstreamRate The Downstream Rate configured on the bridge in kbps.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.20
adGenBridgeCurrentUpstreamRate The Upstream Rate current status on the bridge in kbps.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.21
adGenBridgeCurrentDownstreamRate The Downstream Rate current status on the bridge in kbps.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.22
adGenBridgeRateControl Mode that divides the bridge rates over the links. Bridge Rate Control On is 1 Bridge Rate Control Off is 2	AdGenBridgeRateControlr/w Type Values: 1 rateControlOn 2 rateControlOff	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.23
adGenBridgeAlarmSuppress Indicates whether or not alarms will be generated by this Bridge group. It is only applicable if rowStatus = active.	AdGenBridgeAlarmSuppressr/w Type Values: 1 suppress 2 noSuppress	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.24
adGenBridgeSecondaryUpstreamRate The Secondary Upstream Rate threshold configured on the bridge in kbps. This is only a threshold used to trigger an alarm. A non-zero value enables the alarm associated with the provisioned threshold, default is disable…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.25
adGenBridgeSecondaryDownstreamRate The Secondary Downstream Rate threshold configured on the bridge in kbps. This is only a threshold used to trigger an alarm. A non-zero value enables the alarm associated with the provisioned threshold, default is disab…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.3.1.26

Row creation adds/maps the physical link to a bridge.

adGenBridgePhylMapEntry row .1.3.6.1.4.1.664.5.67.1.16.1.5.1

An entry in the PHYL Map table.
This entry is represents one link that
is associated with a bridge.

Indexes

adGenBridgePhylMapBridgeIfIndex adGenBridgePhylMapPhylIfIndex

Column	Syntax	OID
adGenBridgePhylMapBridgeIfIndex The ifIndex value of the Bridge to which the physical link is mapped.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.1
adGenBridgePhylMapPhylIfIndex The ifIndex value of the physical link.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.2
adGenBridgePhylMapOperStatus The current operational status of the Bridge-PHYL mapping indicating if the physical link is actively participating in the Bridge. This can be down if the row status of the BridgePhyl Map entry is down, the row status o…	AdGenBridgePhylOperStatus Type Values: 1 up 2 down 3 testing 4 unknown	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.3
adGenBridgePhylMapLastChange The value of sysUpTime at the time this Bridge-PHYL mapping entered its current operational state.	AdGenBridgeLastChange	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.4
adGenBridgePhylMapLastError The string describing the last error experienced.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.5
adGenBridgePhylMapRowStatus This object is used to create a new row or modify or delete an existing row in this table. Creating a row adds the PHYL to the Bridge. Setting this value to 'active' indicates that the Bridge-PHYL mapping is administrat…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.67.1.16.1.5.1.6

Displays the status of the available PHYLs in the system,
including which Bridge (if any) a PHYL is associated.
It also indicates the installed status of a certain
PHYL.

adGenBridgePhylStatusEntry row .1.3.6.1.4.1.664.5.67.1.16.1.6.1

An entry in the PHYL Status table.
This entry is represents one link.

Indexes

adGenBridgePhylStatusPhylIfIndex

Column	Syntax	OID
adGenBridgePhylStatusPhylIfIndex The ifIndex value of the physical link. IANA type should be propVirtual(53).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.67.1.16.1.6.1.1
adGenBridgePhylStatusBridgeIfIndex The ifIndex value of the Bridge of which this physical link is apart. A value of '0' indicates that the link is currently not mapped to any Bridge. IANA type should be linegroup(210).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.664.5.67.1.16.1.6.1.2
adGenBridgePhylStatusBridgeType Indicates the type (if any) of bridge with which this PHYL is associated.	AdGenBridgeType Type Values: 1 notProvisioned 2 efm 3 tr101 4 ima 5 linkAggregation 6 macSwitched 7 ppp 8 atm	.1.3.6.1.4.1.664.5.67.1.16.1.6.1.3
adGenBridgePhylStatusInstallStatus Indicates whether or not the physical interface associated with this PHYL exists.	AdGenBridgePhylInstalled Type Values: 1 uninstalled 2 installed	.1.3.6.1.4.1.664.5.67.1.16.1.6.1.4
adGenBridgePhylStatusOperStatus The current operational status of the Bridge-PHYL Mapping. This status should match the adGenBridgePhylMapOperStatus of the corresponding row in the adGenBridgePhylMapTable. The current operational status of the Bridge-…	AdGenBridgePhylOperStatus Type Values: 1 up 2 down 3 testing 4 unknown	.1.3.6.1.4.1.664.5.67.1.16.1.6.1.5

The Bridge Protection Group table.  A unique Bridge Protection Group is created
to protect bonding engine. This fecilitates creating a Protection Group and
adding or removing Protection Slots (PM slots) and Protected Slots (AM slots) to or
from an existing Protection Groups. The Protection or Protected slots can be added
or removed when the Protection Group Row Status is in active state. The Last Error
string will return the error message if for some reason the slots cannot be added
(for e.g. Bridge Type mismatch) or the Protection Group cannot be created. There
are no variables in this table that needs to be set before the row status can be
set to active.

adGenBridgeProtectionGroupEntry row .1.3.6.1.4.1.664.5.67.1.16.1.9.1

An entry in the Bridge Protection Group table. This entry is
used to model a protection group for a protection engine.

Indexes

adGenBridgeProtectionGroupGroupIndex

Column	Syntax	OID
adGenBridgeProtectionGroupGroupIndex A unique value to identify this Bridge Protection Group.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.1
adGenBridgeProtectionGroupBridgeType Indicates the type of bridge this Protection Group is created for. This must be compatible with the Protection and Protected Module slot bridge type.	AdGenBridgeTyper/w Type Values: 1 notProvisioned 2 efm 3 tr101 4 ima 5 linkAggregation 6 macSwitched 7 ppp 8 atm	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.2
adGenBridgeProtectionGroupName The textual name given to this Protection Group.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.3
adGenBridgeProtectionGroupProtectingSlots A bit map of Protection Module slots part of this Protection Group. Displays the Protection Modules in this Protection Group. Slot 1 0x00000001 Slot 2 0x00000002 Slot 3 0x00000004 Slot 4 0x00000008 Slot 5 0x00…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.4
adGenBridgeProtectionGroupProtectedSlots A bit map of Bonding Engine slots to be protected (part of this Protection Group). Displays the Protecting Modules in this Protection Group. Slot 1 0x00000001 Slot 2 0x00000002 Slot 3 0x00000004 Slot 4 0x0000000…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.5
adGenBridgeProtectionGroupAddProtectingModule Add a Protecting Module (slot) to the Protection Group identified by adGenBridgeProtectionGroupIndex.	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.6
adGenBridgeProtectionGroupAddProtectedModule Add a Protected Module (slot) to the Protection Group identified by adGenBridgeProtectionGroupIndex.	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.7
adGenBridgeProtectionGroupRmvProtectingModule Remove a Protecting Module (slot) from the Protection Group identified by adGenBridgeProtectionGroupIndex.	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.8
adGenBridgeProtectionGroupRmvProtectedModule Remove a Protected Module (slot) from the Protection Group identified by adGenBridgeProtectionGroupIndex.	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.9
adGenBridgeProtectionGroupWaitToRestoreTime In case of a revertive swicth, this indicates the time in minutes to wait before a switch back can take place. Wait To Restore time is set for the whole group and is applicable to all the Protected Slots (AMs) in the gr…	Integer32r/w Constraints: range: 1-20	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.10
adGenBridgeProtectionGroupLastError The string describing the last error experienced provisioning the Protection Group or adding or removing Protection or Protected slots.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.11
adGenBridgeProtectionGroupRowStatus This object is used to create a new row or modify or delete an existing row in this table. Creating a row adds either a Protected Module or a Protecting Module to a Protection Group. Setting this value to 'active' indic…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.67.1.16.1.9.1.12

The Bridge Protection table containing protection related provisioning
for each of the Protected Modules or Protection Modules. This is
a static table for all the slots in the system. The Protected Modules and
Protection Modules forming a Protection Group are identified by the
adGenBridgeProtectionGroupTable.

adGenBridgeProtectionEntry row .1.3.6.1.4.1.664.5.67.1.16.1.10.1

An entry in the Bridge Protection table. This entry is
used to provision the protection related parameters for bonding
engine protection. These parameters are provisioned for Protected
Module slots and Protection Module…

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenBridgeProtectionGroupIndex Displays the Protection Group Index this slot is part of. If this slot is not part of any Protection Group, then this value will be zero.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.1
adGenBridgeProtectionBridgeType This is the value read from the module that is plugged into the slot. If bridge type of this module is incompatible with the Bridge Type of the Protection Group this module is part of then an alarm will be generated.	AdGenBridgeType Type Values: 1 notProvisioned 2 efm 3 tr101 4 ima 5 linkAggregation 6 macSwitched 7 ppp 8 atm	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.2
adGenBridgeProtectionVersion This must be compatible with Protection and Protected Modules. A higher version Protection Module can protect a lower or equal version Protected module. This versioning is done to make sure that the Protection Module ha…	AdGenProtectionVersion Type Values: 0 notsupported 1 version1	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.3
adGenBridgeProtectionSlot This is a read only value and indicates the slot number of this entry.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.4
adGenBridgeProtectionState This is a read only value and indicates state of the Protection or Protected Module. A value of zero indicates the module plugged into this slot is not being protected or is not protecting another module. A non-zero val…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.5
adGenBridgeProtectionPriority This is the priority of the Protected Modules within the protection group in case priority protection is enabled. This value can be set to zero. If all the Protected Modules priority is set to zero then priority protect…	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.6
adGenBridgeProtectionRevertiveSwitch Indicates whether revertive switch is enabled or not for this Protected Module. This item is not intended for the Protection Module and is ignored.	AdGenBridgeProtectionRevertiveSwitchr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.7
adGenBridgeProtectionLockout Indicates whether lockout is enabled or not for this Module.	AdGenBridgeProtectionLockoutr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.8
adGenBridgeProtectionManualSwitch Indicates whether to do a manual switch to protection or to manual switch back from protect. Not intended for the Protection Module and is ignored.	AdGenBridgeManualSwitchr/w Type Values: 1 switchToProtect 2 switchToNonProtect	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.9
adGenBridgeProtectionManualSwitchTime In case a manual switch is triggered, this time in minutes indicates for how long the manual switch will be in effect. This item is not intended for the Protection Module and is ignored.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.10
adGenBridgeProtectionErrorStatus Displays error status in case the manual switch command fails.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.10.1.11

The Bridge Name Lookup table. As each bridge receives a name
it is inserted into a lookup table along with it's ifIndex.

adGenBridgeNameLookupEntry row .1.3.6.1.4.1.664.5.67.1.16.1.12.1

An entry in the Bridge Name Lookup table. This entry is
used to store the bridge IfIndex and indexed by the name.

Indexes

adGenBridgeNameLookupIndex

Column	Syntax	OID
adGenBridgeNameLookupIndex The sring name value of the the bridge enity	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.1.12.1.1
adGenBridgeNameIfIndex The Bridge IfIndex that is retrieved from the table	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.664.5.67.1.16.1.12.1.2

Activation of a row in this table causes the TA5000 to perform the following:
1) Verify that all pertinent parameters are set.
2) Verify that there are resources available to perform the requested operation
3) If resources are available then apply to the GenBridge and GenBridgePhylMap tables
This table abstracts the user from internal bandwidth constraints, AM incompatabilities, and
other TA5000 limitations that will change over time. If a requested operation cannot
occur then the status string will be set with an appropriate error.

adGenEasyBridgeEntry row .1.3.6.1.4.1.664.5.67.1.16.2.2.1

Each entry corresponds to a different bridge. An entry will be deleted after 2 minutes of
inactivity. This table is indexed by the values returned from the
adGenEasyBridgeIndexNext OID.

Indexes

adGenEasyBridgeIndex

Column	Syntax	OID
adGenEasyBridgeIndex This is an arbitrary index assigned by the adGenEasyBridgeIndexNext OID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.1
adGenEasyBridgeName This object must be set before a row is activated whether this row is 'Create' or 'Modify'. If it is 'Create' then this string will be set in the adGenBridgeName OID. If the row is 'Modify' then this name will only be u…	OctetStringr/w Constraints: range: 1-50	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.2
adGenEasyBridgeType The intended type of this bridge EFM, IMA, TR-101, etc.	AdGenBridgeTyper/w Type Values: 1 notProvisioned 2 efm 3 tr101 4 ima 5 linkAggregation 6 macSwitched 7 ppp 8 atm	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.3
adGenEasyBridgeCreateOrModify This OID indicates if this row is attempting to create a new bridge or modify an existing one. If the mode is 'create' then the bridge will be created with the parameters in this table unless they are invalid (such as a…	Enumerationr/w Enumerated Values: 1 create 2 modify	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.4
adGenEasyBridgeUpstreamRate This object specifies the rate of the bridge for the upstream direction in Kbps. This parameter helps the agent determine the location of the bridge as well as the rate of each of the links associated with this bridge. …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.5
adGenEasyBridgeDownstreamRate This object specifies the rate of the bridge for the downstream direction in Kbps. This parameter helps the agent determine the location of the bridge as well as the rate of each of the links associated with this bridge…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.6
adGenEasyBridgeMemberPhyls This object is a comma delimited string of ifIndices. Each ifIndices corresponds to a GenBridgePhyl that should be attached to the bridge. This string must contain at least one ifIndex on a 'create' operation. For examp…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.7
adGenEasyBridgeMinNumActivePhyls This object specifies the genBridgeMinNumActivePhyls value. It must always be at most the same number as phyls specified in adGenEasyBridgeMemberPhyls. If the number of phyls specified by adGenEasyBridgeMemberPhyls is g…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.8
adGenEasyBridgeStatusString This object indicates the status of the last attempted activation of this row. It will indicate pass/fail status as well as reasons in the case of a failure.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.9
adGenEasyBridgeRowStatus For this row to go active all pertinent parameters must be set (see individual parameter descriptions) as well as the agent must be able to create a bridge or modify the selected bridge. If an activate fails then the ad…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.10
adGenEasyBridgeRateControl	AdGenBridgeRateControlr/w Type Values: 1 rateControlOn 2 rateControlOff	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.11
adGenEasyBridgeAddMemberPhyls This object is a comma delimited string of ifIndices. This OID is referred to when adGenEasyBridgeCreateOrModify is set to modify(2), which must be done prior to setting this OID. Each ifIndex corresponds to a GenBridge…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.12
adGenEasyBridgeDeleteMemberPhyls This object is a comma delimited string of ifIndices. This OID is referred to when adGenEasyBridgeCreateOrModify is set to modify(2), which must be done prior to setting this OID. Each ifIndex corresponds to a GenBridge…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.664.5.67.1.16.2.2.1.13

Table contains instances that are created when there is a request to a bulk bridge instance.

adGenBridgeBulkInstanceEntry row .1.3.6.1.4.1.664.5.67.1.16.4.1.1

Index is the slot number.

Indexes

ADTRAN-GENSLOT-MIBadGenSlotInfoIndex

Column	Syntax	OID
adGenBridgeBulkInstance Used to index the TlV table; Each time this is called by slot it creates an instance for that viewer. Once an instance is created, it may be found by doing a get on adTa5kTlvBySlotInstance with the instance number	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.664.5.67.1.16.4.1.1.1