A3Com-RIP-IPextns-r4-MIB Table View

This table contains parameters that affect the
operation of RIP for IP.

a3RipIpCtlEntry row .1.3.6.1.4.1.43.2.8.2.1

Each entry contains parameters specific to each
network port on this system.

Indexes

a3RipIpPortIndex

Column	Syntax	OID
a3RipIpPortIndexmandatory This provides the port index to which the RIP-IP parameters in this table entry apply.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.2.1.1
a3RipIpTalkCtlmandatory If talk (1) is specified, RIP-IP sends update and request packets on the specified port. If noTalk (2) is specified, no updates or requests are sent over this port. If talk(1) is specified, 3RipIpDynNbr…	Enumerationr/w Enumerated Values: 1 talk 2 noTalk	.1.3.6.1.4.1.43.2.8.2.1.2
a3RipIpListenCtlmandatory If listen (1) is selected, RIP-IP receives and processes incoming update and request packets. If a3RipIpTalkCtl is set to noTalk (2), this system does not send any response packets for the request packets it receives.	Enumerationr/w Enumerated Values: 1 listen 2 noListen	.1.3.6.1.4.1.43.2.8.2.1.3
a3RipIpTrustedNbrCtlmandatory This object controls how the list of trusted neighbors in a3RipIpTrustedNbrTable is to be interpreted. If this is set to include (1), RIP-IP will accept routing packets from the set of addresses in a3RipIpTrustedNbrTab…	Enumerationr/w Enumerated Values: 1 include 2 exclude	.1.3.6.1.4.1.43.2.8.2.1.4
a3RipIpPoisonCtlmandatory This parameter determines how split horizon is performed. To achieve split horizon, RIP-IP refrains from advertising a route to a port if the gateway for this route can be reached on the same port. If poison (1) is s…	Enumerationr/w Enumerated Values: 1 poison 2 noPoison	.1.3.6.1.4.1.43.2.8.2.1.5
a3RipIpTriggerCtlmandatory This parameter determines if RIP-IP sends trigger update packets. Trigger update packets are sent when a route's metric has changed. By sending these update packets, RIP does not need to wait for the update interval, …	Enumerationr/w Enumerated Values: 1 trigger 2 noTrigger	.1.3.6.1.4.1.43.2.8.2.1.6
a3RipIpDefMetricmandatory This parameter specifies whether RIP-IP advertises the default route. The default route is the network with internet address 0.0.0.0 and is reported with a metric equal to the value of this parameter. If this is set …	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.7
a3RipIpExtPolCtlmandatory This parameter controls which routes learned by the Exterior Gateway Protocol (EGP) are reported by RIP-IP. If this is set to all (1), all routes learned from EGP or BGP are reported, provided those routes are allowed …	Enumerationr/w Enumerated Values: 1 all 2 none 3 include 4 exclude	.1.3.6.1.4.1.43.2.8.2.1.8
a3RipIpIntPolCtlmandatory This parameter determines which routes learned by an Interior Gateway Protocol (IGP) are reported by RIP-IP. If this is set to all (1), all routes learned from an IGP are reported, provided those routes…	Enumerationr/w Enumerated Values: 1 all 2 none 3 include 4 exclude	.1.3.6.1.4.1.43.2.8.2.1.9
a3RipIpNetPolCtlmandatory This parameter determines which routes are reported by RIP-IP. The policies defined by this object and a3RipIpNetPolTable overrides the policies defined in a3RipIpIntPolCtl/Table, a3RipIpExtPolCtl/Table, and a3RipIpS…	Enumerationr/w Enumerated Values: 1 all 2 none 3 include 4 exclude	.1.3.6.1.4.1.43.2.8.2.1.10
a3RipIpRcvPolCtlmandatory This parameter is used to filter routing updates from trusted neighbors. It allows control over which RIP routes are received and stored in the routing table. If this is set to all (1), all routes rep…	Enumerationr/w Enumerated Values: 1 all 2 none 3 include 4 exclude	.1.3.6.1.4.1.43.2.8.2.1.11
a3RipIpStaPolCtlmandatory This parameter is used to filter the reporting of static routes. It allows control over which static RIP routes are reported. If this is set to all (1), all static routes are reported, provided those ro…	Enumerationr/w Enumerated Values: 1 all 2 none 3 include 4 exclude	.1.3.6.1.4.1.43.2.8.2.1.12
a3RipIpUnnAdvCtlmandatory This parameter specifies which routes are reported by RIP updates sent over an unnumbered link. If this object is set to subnetAdvUnn (1), RIP explicitly reports each subnetted route the system knows about. If this ob…	Enumerationr/w Enumerated Values: 1 subnetAdvUnn 2 netAdvUnn	.1.3.6.1.4.1.43.2.8.2.1.13
a3RipIpBcastCtlmandatory This object specifies the destination IP address to which RIP updates are sent over this port. If this object is set to subnetBcast(1), the RIP advertisement is sent using a directed broadcast IP address as its destina…	Enumerationr/w Enumerated Values: 1 subnetBcast 2 all1sBcast	.1.3.6.1.4.1.43.2.8.2.1.14
a3RipIpExtPolAllMetmandatory When a3RipIpExtPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via EGP or BGP. If this object is set to zero, the metric is calculated from the metric learned from EGP or BG…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.15
a3RipIpIntPolAllMetmandatory When a3RipIpIntPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via OSPF or IISIS. If this object is set to zero, the metric is calculated from the metric learned from OSPF o…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.16
a3RipIpNetPolAllMetmandatory When a3RipIpNetPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via RIP. If this object is set to zero, the metric is taken directly from the routing table.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.17
a3RipIpRcvPolAllMetmandatory When a3RipIpRcvPolCtl is set to all, this object specifies the metric stored in the routing table when routing updates are received via RIP (from trusted neighbors).	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.18
a3RipIpStaPolAllMetmandatory When a3RipIpStaPolCtl is set to all, this object specifies the metric used in RIP updates of static routes (ie, those routes entered by a user). If this object is set to zero, the metric is calculated from the metric…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.2.1.19
a3RipIpDynNbrCtlmandatory When a3RipIpDynNbrCtl is set to dynamicNbr over FR or X.25, and -RIP CONTrol is set to TALK, the neighbor list is learnt dynamically as InArp learn the IP addresses of the dlcis or as addresses are added to the ARP ta…	Enumerationr/w Enumerated Values: 1 dynamicNbr 2 noDynamicNbr	.1.3.6.1.4.1.43.2.8.2.1.20
a3RipIpAggregateCtlmandatory This parameter determines if RIP-IP aggregates subnetworks with variable-length subnet masks into one network.	Enumerationr/w Enumerated Values: 1 aggregate 2 noAggregate	.1.3.6.1.4.1.43.2.8.2.1.21
a3RipIpDeAggregateCtlmandatory This parameter determines if RIP-IP de-aggregate a network into many subnetted network.	Enumerationr/w Enumerated Values: 1 deAggregate 2 noDeAggregate	.1.3.6.1.4.1.43.2.8.2.1.22
a3RipIpNBMAmodeCtlmandatory This parameter determines if the underlying NBMA network is full-mesh or non-mesh. Partial-mesh is treated as non-mesh. When this object is set to fullMesh(1), RIP-IP advertises routes based on regular split-horizon. …	Enumerationr/w Enumerated Values: 1 fullMesh 2 nonMesh	.1.3.6.1.4.1.43.2.8.2.1.23

The table contains a list of addresses learned via EGP
that are to be included or excluded from RIP reports.

a3RipIpExtPolEntry row .1.3.6.1.4.1.43.2.8.3.1

Each entry contains a single IP destination address.
This destination is either included or excluded from
RIP reports about routes learned via EGP. Each entry
also contains a metric to be used in the reports.

Indexes

a3RipIpExtPolPort a3RipIpExtPolAddr

Column	Syntax	OID
a3RipIpExtPolPortmandatory This defines the port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.3.1.1
a3RipIpExtPolAddrmandatory This specifies a route destination learned via EGP that is to be included or excluded (based on a3RipIpExtPolCtl) from RIP reports.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.3.1.2
a3RipIpExtPolMetricmandatory The metric that is to be used in RIP reports of this route. If a metric value in the range of 1 to 15 is specified, the route, together with the specified metric, is reported. If the metric 0 is specified, the routing…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.3.1.3
a3RipIpExtPolStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.3.1.4

The table contains a list of addresses learned via an IGP
other than RIP that are to be included or excluded from 
RIP reports.

a3RipIpIntPolEntry row .1.3.6.1.4.1.43.2.8.4.1

Each entry contains a single IP destination address.
This destination is either included or excluded from
RIP reports. Each entry also contains a metric to be
used in the reports.

Indexes

a3RipIpIntPolPort a3RipIpIntPolAddr

Column	Syntax	OID
a3RipIpIntPolPortmandatory This defines the port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.4.1.1
a3RipIpIntPolAddrmandatory This specifies a route destination learned via an IGP that is to be included or excluded (based on a3RipIpIntPolCtl) from RIP reports.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.4.1.2
a3RipIpIntPolMetricmandatory The metric that is to be used in RIP reports of this route. It a metric value in the range of 1 to 15 is specified, the route, together with the specified metric, is reported. If the metric 0 is specified, the routing…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.4.1.3
a3RipIpIntPolStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.4.1.4

The table contains a list of addresses that are to 
be included or excluded from RIP reports.  Note,
Network Policy overrides Static Policy, Interior
Policy, and Exterior Policy in deciding whether a
route is to be reported.

a3RipIpNetPolEntry row .1.3.6.1.4.1.43.2.8.5.1

Each entry contains a single IP destination address.
This destination is either included or excluded from
RIP reports. Each entry also contains a metric to be
used in the reports.

Indexes

a3RipIpNetPolPort a3RipIpNetPolAddr

Column	Syntax	OID
a3RipIpNetPolPortmandatory This defines the port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.5.1.1
a3RipIpNetPolAddrmandatory This specifies a route destination that is to be included or excluded (based on a3RipIpNetPolCtl) from RIP reports.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.5.1.2
a3RipIpNetPolMetricmandatory The metric that is to be used in RIP reports of this route. If a metric value in the range of 1 to 15 is specified, the route, together with the specified metric, is reported. If the metric 0 is specified, the routing…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.5.1.3
a3RipIpNetPolStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.5.1.4

The table contains a list of addresses learned via trusted 
neighbors that are to be received and stored in the routing
table.

a3RipIpRcvPolEntry row .1.3.6.1.4.1.43.2.8.6.1

Each entry contains a single IP destination address.
This destination is either stored or not stored when
RIP reports from trusted neighbors are received. Each
entry also contains a metric to be used in the routing
ta…

Indexes

a3RipIpRcvPolPort a3RipIpRcvPolAddr

Column	Syntax	OID
a3RipIpRcvPolPortmandatory This defines the port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.6.1.1
a3RipIpRcvPolAddrmandatory This specifies a route destination that is to be stored or not stored (based on a3RipIpRcvPolCtl) when RIP reports from trusted neighbors are received.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.6.1.2
a3RipIpRcvPolMetricmandatory The metric that is to be used in the routing table entry for this route. It a metric value in the range of 1 to 15 is specified, the route, together with the specified metric, is stored. If the metric 0 is specified,…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.6.1.3
a3RipIpRcvPolStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.6.1.4

The table contains a list of static addresses 
that are to be included or excluded from RIP reports.

a3RipIpStaPolEntry row .1.3.6.1.4.1.43.2.8.7.1

Each entry contains a single IP destination address
representing a static route. This destination is either
included or excluded from RIP reports. Each entry also
contains a metric to be used in the reports.

Indexes

a3RipIpStaPolPort a3RipIpStaPolAddr

Column	Syntax	OID
a3RipIpStaPolPortmandatory This defines the port to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.7.1.1
a3RipIpStaPolAddrmandatory This specifies a route destination learned statically that is to be included or excluded (based on a3RipIpStaPolCtl) from RIP reports.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.7.1.2
a3RipIpStaPolMetricmandatory The metric that is to be used in RIP reports of this route. It a metric value in the range of 1 to 15 is specified, the route, together with the specified metric, is reported. If the metric 0 is specified, the routing…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.43.2.8.7.1.3
a3RipIpStaPolStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.7.1.4

This table contains a list of neighbor addresses that
RIP-IP uses to determine to which neighbors it should
send update packets.  RIP-IP neighbors are router
that share a common network and participate in the
RIP-IP protocol.  Each RIP-IP packet can be either broadcast
or addressed individually to each neighbor.  If no
neighbors are configured on the port, RIP broadcasts
update packets on the port.

a3RipIpNeighborEntry row .1.3.6.1.4.1.43.2.8.8.1

Each entry contains information about a single
RIP-IP neighbor. The information include the
neighbor's IP address as well as the port from
which it can be reached.

Indexes

a3RipIpNeighborPort a3RipIpNeighborAddr

Column	Syntax	OID
a3RipIpNeighborPortmandatory This indicates the port from which this neighbor can be reached. The neighbor must be attached to the same network as this port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.8.1.1
a3RipIpNeighborAddrmandatory This specifies the IP address of the RIP-IP neighbor.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.8.1.2
a3RipIpNeighborStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.8.1.3

This table contains a list of RIP-IP neighbors 
from which RIP-IP accepts packets.  If this table
contains no entries for a particular port, RIP-IP
will accept all packets from that port.

a3RipIpTrustedNbrEntry row .1.3.6.1.4.1.43.2.8.9.1

Each entry identifies a trusted neighbor from which
RIP-IP will accept routing packets.

Indexes

a3RipIpTrustedNbrPort a3RipIpTrustedNbrAddr

Column	Syntax	OID
a3RipIpTrustedNbrPortmandatory This specifies the port for which this table entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.8.9.1.1
a3RipIpTrustedNbrAddrmandatory This identifies the IP address of a trusted neighbor from which RIP-IP will accept (or not, depending on the value of a3RipIpTrustedNbrCtl) routing packets.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.8.9.1.2
a3RipIpTrustedNbrStatusmandatory This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.8.9.1.3

This table specifies the operations to be performed
on metrics imported from other routing update protocols
before they are reported by RIP.

a3RipIpImpMetEntry row .1.3.6.1.4.1.43.2.8.10.1

Each entry specifies the operations to be performed
on the metric imported from a specific routing update
protocol before it is reported by RIP.

Indexes

a3RipIpImpMetProtocol

Column	Syntax	OID
a3RipIpImpMetProtocolmandatory This object identifies the routing update protocol from which metrics (and routes) are imported.	Enumeration Enumerated Values: 1 ospf 2 iisis 3 egp 4 bgp 5 static	.1.3.6.1.4.1.43.2.8.10.1.1
a3RipIpImpMetOperationmandatory This specifies the operation to be performed on the native protocol metric before it is reported by RIP.	Enumerationr/w Enumerated Values: 1 multiply 2 divide	.1.3.6.1.4.1.43.2.8.10.1.2
a3RipIpImpMetOperandmandatory This specifies the operand of the operation specified by the corresponding instance of a3RipIpImpMetOperation. See the comments describing this table for more details. If this object has the value 0, the …	Integer32r/w Constraints: range: 0-1073741823	.1.3.6.1.4.1.43.2.8.10.1.3