A3Com-Dvmrp-r1-MIB Table View

This table contains entries of parameters associated with every port
or tunnel.

a3ComDvmrpPortEntry row .1.3.6.1.4.1.43.2.28.2.1.1

Each entry contains information for a spcified port or tunnel.

Indexes

a3ComDvmrpPortIndex

Column	Syntax	OID
a3ComDvmrpPortIndexmandatory The port number or tunnel ID of which this entry applies. The tunnel ID starts with 1025 and end with 1056, i.e. total tunnel number is limited to 32.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.1.1.1
a3ComDvmrpPortControlmandatory This object allows the multicast routing to run with DVMRP or not.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.43.2.28.2.1.1.2
a3ComDvmrpPortMetricmandatory This object specifies the cost to the given port or tunnel. A value of 32 is considered 'infinity'.	Integer32r/w Constraints: range: 1-31	.1.3.6.1.4.1.43.2.28.2.1.1.3
a3ComDvmrpPortRateLimitmandatory This object specifies the bandwidth in Kbits/second that will be allocated for the multicast datagrams traffic. If set the value to 0 then the full bandwidth of the port will be applied.	Integer32r/w Constraints: range: 0-100000	.1.3.6.1.4.1.43.2.28.2.1.1.4
a3ComDvmrpPortAggregateCtrlmandatory This object controls the way to advertise routes.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.43.2.28.2.1.1.5

This table contains multicast addresses to be scoped for each port or
tunnel.

a3ComDvmrpBoundaryAddrEntry row .1.3.6.1.4.1.43.2.28.2.2.1

Each entry contains a single or a range of multicast addresses to be
scoped over a specific port or tunnel.

Indexes

a3ComDvmrpBoundaryAddrPort a3ComDvmrpBoundaryAddrIpAddr

Column	Syntax	OID
a3ComDvmrpBoundaryAddrPortmandatory The port or tunnel number to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.2.1.1
a3ComDvmrpBoundaryAddrIpAddrmandatory This allows you to configure a single or a set of multicast addresses to be scoped that they do not get forwarded beyond a boundary router.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.2.1.2
a3ComDvmrpBoundaryAddrMaskmandatory This is the subnet mask associated with a3ComDvmrpBoundaryIpAddr of this entry. If this is not specified, the value 255.255.255.255 is used.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.2.1.3
a3ComDvmrpBoundaryAddrStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.2.1.4

This table contains a list of source subnet in MOSPF domain.

a3ComDvmrpMospfEntry row .1.3.6.1.4.1.43.2.28.2.3.1

Each entry contains a source subnet in MOSPF domain to be advertised
or not to be advertised to the DVMRP domain.

Indexes

a3ComDvmrpMospfIpAddr a3ComDvmrpMospfIpMask

Column	Syntax	OID
a3ComDvmrpMospfIpAddrmandatory Source subnet's IP address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.3.1.1
a3ComDvmrpMospfIpMaskmandatory This is subnet mask associated with a3ComDvmrpMospfIpAddr. It is a number of contiguous leading 1s, i.e. if the value is 1, it indicates the subnet mask is 128.0.0.0, or if the value is 8 then the subnet mask is 255.0.0…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.3.1.2
a3ComDvmrpMospfMetricmandatory The routing metric to this source subnet. It ranges from 1 to 31.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.3.1.3
a3ComDvmrpMospfActionmandatory If this object is set to aggregate(1), then this source subnet, if learned from MOSPF, is advertised to DVMRP domain in aggregate form. If this object is set to individual(2), then this source subnet, if learned from MO…	Enumerationr/w Enumerated Values: 1 aggregate 2 individual 3 reject	.1.3.6.1.4.1.43.2.28.2.3.1.4
a3ComDvmrpMospfStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.3.1.5

This table contains a list of neighbors entries for each X.25 or
Frame-Relay networks.

a3ComDvmrpNeighborEntry row .1.3.6.1.4.1.43.2.28.2.4.1

Each entry contains a single X.25 DTE address or a Frame-Relay DLCI.

Indexes

a3ComDvmrpNeighborPort a3ComDvmrpNeighborType a3ComDvmrpNeighborAddr

Column	Syntax	OID
a3ComDvmrpNeighborPortmandatory The port number to which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.4.1.1
a3ComDvmrpNeighborTypemandatory This object specifies the media type of the port.	Enumeration Enumerated Values: 2 x25 4 frame-relay	.1.3.6.1.4.1.43.2.28.2.4.1.2
a3ComDvmrpNeighborAddrmandatory This object specifies an X.25 DTE address or a Frame-Relay DLCI.	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.43.2.28.2.4.1.3
a3ComDvmrpNeighborStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.4.1.4

This table contains entries of tunnel.

a3ComDvmrpTunnelEntry row .1.3.6.1.4.1.43.2.28.2.5.1

Each entry contains parameters associated with a specific tunnel.

Indexes

a3ComDvmrpTunnelId

Column	Syntax	OID
a3ComDvmrpTunnelIdmandatory The ID number of which this entry applies. Tunnel ID starts with 1025 and ends with 1056.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.5.1.1
a3ComDvmrpTunnelLocalIpmandatory This object specifies the IP address of local end of a tunnel. It must be one of system's directly connected subnet.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.5.1.2
a3ComDvmrpTunnelRemoteIpmandatory This object specifies the IP address of remote end of a tunnel.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.5.1.3
a3ComDvmrpTunnelTtlmandatory This object specifies the value to be put in IP packet's TTL field when transmits packets through a tunnel.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.43.2.28.2.5.1.4
a3ComDvmrpTunnelStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.5.1.5

The table contains list of subnets not to be aggregated.

a3ComDvmrpAggreExceptEntry row .1.3.6.1.4.1.43.2.28.2.6.1

Each entry contains a range of subnets.

Indexes

a3ComDvmrpAggreExceptIpAddr a3ComDvmrpAggreExceptIpMask

Column	Syntax	OID
a3ComDvmrpAggreExceptIpAddrmandatory This object specifies the IP subnet address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.6.1.1
a3ComDvmrpAggreExceptIpMaskmandatory The subnet mask of ccsIpDvmrpAggreExceptIpAddr. It is an integer value representing number of consecutive leading 1s. i.e. if the value is 1, then the subnet mask is 128.0.0.0, if the value is 8 then the subnet mask is …	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.43.2.28.2.6.1.2
a3ComDvmrpAggreExceptStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.6.1.3

The table contains range of routes to be aggregated.

a3ComDvmrpAggreRangeEntry row .1.3.6.1.4.1.43.2.28.2.7.1

Each entry contains a range of routes.

Indexes

a3ComDvmrpAggreRangeIpAddr a3ComDvmrpAggreRangeIpMask

Column	Syntax	OID
a3ComDvmrpAggreRangeIpAddrmandatory This object specifies the IP subnet address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.7.1.1
a3ComDvmrpAggreRangeIpMaskmandatory The subnet mask of ccsIpDvmrpAggreRangeIpAddr. It is an integer value representing number of consecutive leading 1s. i.e. if the value is 1, then the subnet mask is 128.0.0.0, if the value is 8 then the subnet mask is 2…	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.43.2.28.2.7.1.2
a3ComDvmrpAggreRangeMetricmandatory This object specifies the cost to the above subnet. If set this object to value 0, the metric associated with the aggregate route to be advertised will pick up the best one among all the aggregated routes.	Integer32r/w Constraints: range: 0-31	.1.3.6.1.4.1.43.2.28.2.7.1.3
a3ComDvmrpAggreRangeStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.7.1.4

The table contains destination groups to be or not to be forwarded
to MOSPF domain. This table will take effect only if object
a3ComDvmrpDestGroupPolicy is set to 'destGroup (1)'.

a3ComDvmrpDestGroupEntry row .1.3.6.1.4.1.43.2.28.2.8.1

Each entry contains a destination group to be or not to be forwarded
to MOSPF domain.

Indexes

a3ComDvmrpDestGroupIpAddr a3ComDvmrpDestGroupIpMask

Column	Syntax	OID
a3ComDvmrpDestGroupIpAddrmandatory This object specifies the destination group IP address, the first byte in decimal must be in the range of 224 to 239.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.2.8.1.1
a3ComDvmrpDestGroupIpMaskmandatory This is subnet mask associated with a3ComDvmrpDestGroupIpAddr. It is a number of contiguous leading 1s, i.e. if the value is 1, it indicates the subnet mask is 128.0.0.0, or if the value is 8 then the subnet mask is 255…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.2.8.1.2
a3ComDvmrpDestGroupActionmandatory This object specifies if this destination group needs to be forwarded to MOSPF domain. If set to 'accept (1)', the group is forwarded to MOSPF domain; if set to 'reject (2)' then the group is filtered out.	Enumerationr/w Enumerated Values: 1 accept 2 reject	.1.3.6.1.4.1.43.2.28.2.8.1.3
a3ComDvmrpDestGroupStatusmandatory This object is used to add and delete entries in this table. See the definition of RowStatus for detail.	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.28.2.8.1.4

This table contains multicast route information.

a3ComDvmrpRouteEntry row .1.3.6.1.4.1.43.2.28.3.1.1

Each entry contains route information to a specific subnet or source.

Indexes

a3ComDvmrpRouteSource

Column	Syntax	OID
a3ComDvmrpRouteSourcemandatory The source IP address of this route.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.1.1.1
a3ComDvmrpRouteMaskmandatory This object is logical-anded with the source address before comparing to the value in previous object a3ComDvmrpRouteSource.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.1.1.2
a3ComDvmrpRoutePreHopmandatory The IP address of the upstream router of this route.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.1.1.3
a3ComDvmrpRouteMetricmandatory The routing metric of this route. It's routing-protocol dependenable, for DVMRP, the metric should be in range 1 to 31. The value 32 is considered 'infinity' or unreachable.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.1.1.4
a3ComDvmrpRoutePortmandatory The port number identifies from which this route comes.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.1.1.5
a3ComDvmrpRouteTypemandatory The type of route.	Enumeration Enumerated Values: 1 other 2 direct 3 remote	.1.3.6.1.4.1.43.2.28.3.1.1.6
a3ComDvmrpRouteStatusmandatory The status of route.	Enumeration Enumerated Values: 1 other 2 up 3 down 4 hold-down 5 garbage-collection	.1.3.6.1.4.1.43.2.28.3.1.1.7
a3ComDvmrpRouteProtocolmandatory The routing algorithm to which this route applies.	Enumeration Enumerated Values: 1 other 2 static 3 dvmrp 4 mospf 5 cbt 6 pim	.1.3.6.1.4.1.43.2.28.3.1.1.8
a3ComDvmrpRouteTtlmandatory The time in seconds this route was last updated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.1.1.9
a3ComDvmrpRouteChildmandatory This object identifies ports that connect to child subtree of the multicast tree rooted at a3ComDvmrpRouteSource. Each octet, except the first one which contains a value specified length of this object, contains a bit m…	OctetString	.1.3.6.1.4.1.43.2.28.3.1.1.10
a3ComDvmrpRouteChildTunnelmandatory This object is the same as above but includes tunnel ports only. The first (should say the second) octet specifies ports from 1025 (for tunnel port 1) to 1032, the next octet specifies ports 1033 to 1040, ... etc.	OctetString	.1.3.6.1.4.1.43.2.28.3.1.1.11
a3ComDvmrpRouteLeafmandatory This objec identifies ports that connect to leaf subnet of the multicast tree rooted at a3ComDvmrpRouteSource. The value meaning within each octet is the same as that of a3ComDvmrpRouteChild, except the bit set means th…	OctetString	.1.3.6.1.4.1.43.2.28.3.1.1.12
a3ComDvmrpRouteLeafTunnelmandatory This objec is the same as a3ComDvmrpRouteLeaf object but includes tunnel ports only.	OctetString	.1.3.6.1.4.1.43.2.28.3.1.1.13

This table contains information of each (source, group) pair.

a3ComDvmrpForwardEntry row .1.3.6.1.4.1.43.2.28.3.2.1

Each entry contains forwarding information for a specific (source,
group) pair.

Indexes

a3ComDvmrpForwardSource a3ComDvmrpForwardGroup

Column	Syntax	OID
a3ComDvmrpForwardSourcemandatory This object specifies root's IP address of this (source, group) multicast distribution tree.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.2.1.1
a3ComDvmrpForwardGroupmandatory This object specifies the destination multicast group address of this (source, group) multicast distribution tree.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.2.1.2
a3ComDvmrpForwardTtlmandatory This object specifies the time in seconds left for this (source, group) entry to stay in the forwarding table. When this value reaches 0, this (source, group) entry is deleted from the table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.2.1.3
a3ComDvmrpForwardInPortmandatory This object specifies the incoming port for the multicast datagrams from the source a3ComDvmrpForwardSource.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.2.1.4
a3ComDvmrpForwardOutPortsmandatory This object specifies ports to which multicast datagrams belonging to this (source, group) pair to be forwarded. The value in each octet contains a bit maps of 8 ports, that the significant bit represents the lowest por…	OctetString	.1.3.6.1.4.1.43.2.28.3.2.1.5
a3ComDvmrpForwardOutPortsTunnelmandatory This object is the same as a3ComDvmrpForwardOutPorts object but includes tunnel ports mapping only.	OctetString	.1.3.6.1.4.1.43.2.28.3.2.1.6
a3ComDvmrpForwardScopedmandatory This object specifies if it is a boundary port. If the value of this object is yes(1), it means multicast traffic will not be forwarded on the scoped address, specified in 3ComDvmrpForwardGroup, on this port.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.2.1.7
a3ComDvmrpForwardPruneSentmandatory This object specifies if a Prune message has been sent to its upstream router. A prune message is sent when router wants to leave the multicast delivery tree associated with this (source, group) pair.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.2.1.8

This table contains information of each neighboring router.

a3ComDvmrpNbrRouterEntry row .1.3.6.1.4.1.43.2.28.3.3.1

Each entry contains neighboring router's IP address, DVMRP version,
generation ID, expiration time and status.

Indexes

a3ComDvmrpNbrRouterPort a3ComDvmrpNbrRouterIpAddr

Column	Syntax	OID
a3ComDvmrpNbrRouterPortmandatory The port number or tunnel ID of which this entry applies.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.3.1.1
a3ComDvmrpNbrRouterIpAddrmandatory The IP address of this neighboring router.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.43.2.28.3.3.1.2
a3ComDvmrpNbrRouterGenIdmandatory The generation ID of this neighboring router.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.3.1.3
a3ComDvmrpNbrRouterVerProtocolmandatory The version of DVMRP protocol that this neighboring router is running.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.3.1.4
a3ComDvmrpNbrRouterVerMroutedmandatory The version of 'mrouted' that this neighboring router is running.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.3.1.5
a3ComDvmrpNbrRouterTtlmandatory The time in seconds left for this neighboring router. When the value reaches 0, this entry is deleted from the table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.28.3.3.1.6
a3ComDvmrpNbrRouterLeafStatusmandatory This object specifies if this neighboring router is a leaf node.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.3.1.7
a3ComDvmrpNbrRouterPruneStatusmandatory This object specifies if this neighboring router supports DVMRP prune.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.3.1.8
a3ComDvmrpNbrRouterGenIdStatusmandatory This object specifies if this neighboring router provides generation ID and its router list in the DVMRP probe packet.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.3.1.9
a3ComDvmrpNbrRouterMtraceStatusmandatory This object specifies if this neighboring router supports multicast trace route.	Enumeration Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.43.2.28.3.3.1.10